6700 T Shirt Lotus leaf sleeve

The below steps are detailed for the V7.0 version. If you are using V6.0, the steps will be slightly different.

T-ShirtFlared

Use the BLK M.T.shirt pattern as the basic block to draw this shirt, pls finish drawing the BLK M.T.shirt pattern first.

Edit the neck width of the back piece.
  1. use t6 Pointer tool to select the back shoulder line, click t8 Add Point to Segment tool, left click the point G, enter value in the dialog box and click “OK”, then you can get a new point. Repeat the same steps in the front piece. t9
  2. Hold down Shift key and click t6 Pointer tool to select point G,g,H,h, then use “Delete” key,Mac or¨Backspace“key Windows to delete them. t10
  3. Use tr008 Curve tool to adjust the neck line: active the piece (use pointer tool to left click one segment of the piece), select tr008 Cruve tool, left click and hold down it, drag the cursor to curve the segment. t12 NOTE: If the curve is not smooth enough, you can add more points on the curve by using t14 Add Point Tool to adjust the curve.
    • Draw button stand
  4. Use t6 Pointer tool to select the center front line, select t15 Parallel Line tool, left click the selected line, move the cursor, enter the values and select “permanent”, finally click the blank area or press “Enter” key to finish the operation.t16
    • Draw the hem
  5. Use Pointer tool to select the front shoulder line and front hem line, click t17 Intersection Point tool, hold down Alt (Windows) or Option (Macintosh) or Alt+Windows (Linux) key, the cursor turns in to a cross, click point F, enter the vuales and select “Vertically” then click the “OK” button, you can get two new points. t18
    • repeat the above steps on the back piece t19
  6. Use t6 Pointer tool to select the segments (segments between two new points), click t20 Segment Angle tool, hold down Alt (Windows) or Option (Macintosh) or Alt+Windows (Linux) key and left click point H (the new point of hem), enter the value, click [OK] button to finish the operation.

t21

  1. Use t6 Pointer tool to select point A1 and A2, click [Treatment][Point][Control] to turn them into control points.
  1. Use t6 Pointer tool to select the front center line and front neck line, click t3 Parallel Line tool, left click the selected line, move the cursor to the inner side, enter the values and “attach to the contour”, click the blank area or press “Enter” key to finish the operation

t25

  1. Repeat the above step on the back piece to draw the back collar inner facing:

t26

  1. Cuff change to sleeve opening
  2. Edit the cuff width: use t6 Pointer tool to select the cuff line, click t27 Segment Length, left click the Mid point of the cuff (point M), enter the value and select the option in need, click the [OK] button to finish the operation: t28
  3. Edit the sleeve length use t6 Pointer tool to select the cuff line, hold down the Ctrl+Alt (Windows) or Command+Option (Macintosh) key and click the Pointer icon t6 to open the dialog box. Enter the value and click [OK] button.
t29 > Symmetry the sleeveuse t6 Pointer tool to select the center sleeve line, click t30 Mirror tool, left click the selected line, then the sleeve piece be opened to the complete piece. Press the Backspace (Windows) or Delete (Macintosh) directly to delete the mirror line
t31 3. Draw a flounce on the sleeve 
1measure the length of the cuff and copy it’s value: use t6 Pointer tool to select the cuff line, click t27 Segment Length tool, click one of the extremities of the selected segment. > t32
2 Use Ruffle tool to the flounce: click t33 Ruffle tool, Left-click on the desired location, Dialog box appears, press Ctrl+V (Windows) or Command+V (Mac) to paste the value to the ¨Length〃 colum, tab to next column the input “Height” and “Gap” value , click the blank area or press ¨Enter〃 key to finish the operation: > t34
Now you’ve finished the preliminary pattern of 6700 T Shirt

t35

The left setps are unfold the piece/ setting pieces/ add seam allowance in need.
Pls look at the manual to learn how to use the Mirror tool to unfold the piece, how to set pieces, how to add seam allowance.
1.How to set pieces: http://www.padsystem.com/en/assets/documents/en/pattern/pattern_design_en_ch2_treatment_detail.html
2.How to add seam allowance: http://www.padsystem.com/en/assets/documents/en/pattern/pattern_design_en_ch3.html#tool-image163-seam-allowance