====== Add Marker Assistant ======

> Marker Assistant helps users check over the marker and find out the error, which improve the efficiency and accuracy of the marker planning.

===== Check the marker automatically =====

> Marker Assistant will check four aspects as follows:

> Match: match point which isn’t aligned;

> Missing: miss piece(s) or put extra piece(s) when marker planning;

> Notch: the cutting point is on the notch;

> Overlap: some pieces get overlapped on the simulation area.

> You can use Marker Assistant to check your marker before sending the marker file out to production.

> How to do:

> Click Treatment - Marker Assistant - Marker Assistant Dialog Box - Start:

{{en:marker:marker_release_v7:image80.png|image80}}


> Then the system will show you error message about Match, Missing, Notch or Overlap on the right side of the window:

{{en:marker:marker_release_v7:image81.png|image81}}


> When you click the error message, it will jump to the corresponding layer.

====== Operation Tips for Marker Tools ======

> It will show users the operation tips on the bottom of the window when users click the tool, which helps users learn the software more easily. For example: Pointer tool {{en:marker:marker_release_v7:image9.png|image9}} :

{{en:marker:marker_release_v7:image82.png|image82}}


====== Add Cutting Preview ======

> Users can check the cutting sequence, cutting starting points of the file which is sent out for production in cutting preview.

===== Preview the cutting file =====

>> How to preview your file:

{{en:marker:marker_release_v7:image85.png|image85}}


{{en:marker:marker_release_v7:image87.png|image87}}


> {{en:marker:marker_release_v7:image88.png|image88}}:  /  button.

> {{en:marker:marker_release_v7:image89.png|image89}}:  button.

> {{en:marker:marker_release_v7:image90.png|image90}}: speed of the simulative knife.

> {{en:marker:marker_release_v7:image91.png|image91}}: show previous or next piece(s).

> {{en:marker:marker_release_v7:image92.png|image92}}: show/hide the track line of the knife between pieces.

====== Show The Dart Line ======

> Now it can show the dart lines, users can select to show it if needed. {{en:marker:marker_release_v7:image83.png|image83}}

====== Optimize [Guideline Info] Dialog Box ======

> Simplify the operation, combine two steps into one. That means users can set the guideline and choose color at the same time. {{en:marker:marker_release_v7:image133.png|image133}}

====== Optimize Option Menu [Plaid and Stripes] ======

> Allow users to open [plaid and stripes] dialog box and input value to set plaid directly. But in V6.0, users need to add a line at first in the simulation area by manual and then open the dialog box to set more information about plaid and tripes.

{{en:marker:marker_release_v7:image137.png|image137}}


{{en:marker:marker_release_v7:image136.png|image136}}


=== NOTE ===

> In V6.0, if users didn’t add a guideline at first by manual, the [Option] menu [Plaid and Stripes] will show gray representing not allow to select.

{{en:marker:marker_release_v7:image135.png|image135}}


====== Optimize [Link Pieces] ======

> Optimize [Link Pieces], divide [Halfway] into [Center] and [On Line], enble users operate more easily and quickly. {{en:marker:marker_release_v7:image151.png|image151}}

====== Optimize The Feature of Pattern Refreshment ======

> Now show three columns of the pattern list, users can check and treat the pieces more easily. {{en:marker:marker_release_v7:image94.png|image94}}

{{en:marker:marker_release_v7:image95.png|image95}}


====== Optimize The Feature of Opitcutview ======

> Now it can export multiple fabrics at a time under Opticutview. {{en:marker:marker_release_v7:image93.png|image93}}

====== Optimize The Feature of Auto Save ======

> Avoid missing the unsaved file caused by the unusual shutdown of the computer or crash of the software.

===== Auto save interval: =====

> It automatically saves the current file every 10 seconds by default. Allow users to change Auto save interval as wish:

{{en:marker:marker_release_v7:image96.png|image96}}


===== Revert security copy: =====

> When the software crumbles, the window of auto save revert will appear after re-opening the software. Double-click it to revert the security copy:

{{en:marker:marker_release_v7:image97.png|image97}}