Differences

This shows you the differences between two versions of the page.

--- en:marker:marker_design_ch3_function [2025/07/14 03:20] – [tool_image016 Push Down] administrator
+++ en:marker:marker_design_ch3_function [2025/07/14 03:57] (current) – [Force Piece] administrator
@@ Line 25: / Line 25: @@
 > Or press 2 key directly.
-===== tool_image017 Push Left =====
+===== Push Left =====
+{{en:marker:tool:tool_image017.png|tool_image017}}
 > The Push Left key pushes a piece (or a group of pieces) horizontally toward the end of the Fabric Simulation Area. The piece stops if it touches another piece or the fabric edge.
@@ Line 31: / Line 32: @@
 > Or press 4 key directly.
-===== tool_image018 Push Right =====
+===== Push Right =====
+{{en:marker:tool:tool_image018.png|tool_image018}}
 > The Push Right key pushes a piece (or a group of pieces) horizontally toward the end of the Fabric Simulation Area. The piece stops when it touches another piece or the window’s end.
@@ Line 37: / Line 39: @@
 > Or press 6 key directly.
-===== tool_image019 Rotate =====
+===== Rotate =====
+{{en:marker:tool:tool_image019.png|tool_image019}}
 >> The Rotate key rotates counter-clockwise one or more selected piece(s). - **Set the rotation angle**
@@ Line 56: / Line 59: @@
 >> For more information about Piece Treatment Tolerance, please refer to Chapter 2 Treatment Menu in this manual.
-===== tool_image020 Horizontal Symmetry =====
+===== Horizontal Symmetry =====
+{{en:marker:tool:tool_image020.png|tool_image020}}
 > The Horizontal Symmetry key flips a piece on the marker on a horizontal axis.
@@ Line 72: / Line 76: @@
 > Or press 7 key directly to apply this function.
-===== tool_image021 Vertical Symmetry =====
+===== Vertical Symmetry =====
+{{en:marker:tool:tool_image021.png|tool_image021}}
 >> The Vertical Symmetry key flips a piece on the marker on a vertical axis.
@@ Line 91: / Line 96: @@
 > For more information about Piece Treatment Tolerance, please refer to Chapter 2 Treatment Menu in this manual.
-===== tool_image022 Gap =====
+===== Gap =====
+{{en:marker:tool:tool_image022.png|tool_image022}}
 > The Gap key creates a gap (space) between two pieces.
@@ Line 113: / Line 119: @@
-===== tool_image023 Overlap =====
+===== Overlap =====
+{{en:marker:tool:tool_image023.png|tool_image023}}
 > The Overlap key overlaps two pieces.
@@ Line 135: / Line 142: @@
-===== tool_image024 Fine Rotate CCW =====
+===== Fine Rotate CCW =====
+{{en:marker:tool:tool_image024.png|tool_image024}}
 >> The Fine Rotate CCW key makes a fine rotation counter-clockwise on a selected piece.
@@ Line 162: / Line 170: @@
-===== tool_image025 Fine Rotate CW =====
+===== Fine Rotate CW =====
+{{en:marker:tool:tool_image025.png|tool_image025}}
 > The Fine Rotate CW key makes a fine rotation clockwise on a selected piece.
@@ Line 185: / Line 194: @@
-===== tool_image026 Standby =====
+===== Standby =====
+{{en:marker:tool:tool_image026.png|tool_image026}}
 > This Standby key sends or retrieves a piece or a group of pieces from the Standby Area to the Fabric Simulation Area or vice-versa.
@@ Line 206: / Line 216: @@
 >>   - Use Standby Area with Automatic Nesting: when you use automatic nesting but you don’t want to place some pieces, then you can move those pieces to standby area, and deselect the option “Pieces in Standby Area” in menu [Options]-[Preferences]-[Automatic Engine]. Start automatic nesting after finishing the setting. > 1. The pieces remains the original order in the simulation after moving them to the standby area.
-===== tool_image027 Slide Piece =====
+===== Slide Piece =====
+{{en:marker:tool:tool_image027.png|tool_image027}}
 > The Slide Piece key slides a piece (or a group of pieces) in a desired direction on the Fabric Simulation Area.
@@ Line 225: / Line 236: @@
-===== {{en:marker:tool:tool_image027_1.png}} Force Piece =====
+===== Force Piece =====
 > The Force Piece key allows you to temporarily superimpose pieces on one another.